Projects

Hardware modules I designed, built and tested as part of R&D work.

System project

EKASS.AI

EKASS.AI — AI-Assisted Pedal Assist System

Design stage

A control system for electric bicycles that measures the rider's pedal effort in real time and adjusts motor assistance accordingly. It fuses torque, cadence, crank-angle and IMU data in a 100 Hz control loop and responds to crank-phase changes in under 5 ms. The Cruise, Climb, Glide and Stop-Start riding modes are designed to hold rider effort at roughly 50 W. I led the hardware design and the system architecture.

PlatformRaspberry Pi 4
Kontrol / Control loop100 Hz
Tepki / Response< 5 ms krank faz tepkisi
Sensör / SensorsTork · kadans · krank açısı · IMU
Batarya / Battery36 V 15 Ah (540 Wh)
Limit25 km/h
Sensor FusionReal-Time ControlPedelec

Efficiency and range figures are calculated target values; they have not been verified by field measurement.

Hardware

Hardware modules

Sensored Brushless Motor Controller (ESC)

Design stage Power Electronics

Hall-sensored brushless DC motor controller designed for a 36 V bus. A three-phase MOSFET bridge, a dedicated half-bridge gate driver per phase and an STM32F401 controller on a single board.

Katman / Layers2
Boyut / Size68,5 × 75 mm
Bara / Bus36 V
Güç katı / Power stage6 × IRF3205
Kapı sürücü / Gate driver3 × IR2103S
MCUSTM32F401RCT6
BLDCHalf-BridgeGate DriverHall SensorSTM32
View details

STM32F401 Mini Controller Board

Design stage Embedded Systems

A 53 × 23 mm general-purpose microcontroller board based on the STM32F401. It works as a standalone development board and, with a few changes, can be embedded into a larger system as a controller module.

Katman / Layers2
Boyut / Size53 × 23 mm
MCUSTM32F401RCT6
Bellek / Memory32 Mbit SPI flash
Bağlantı / ConnectivityUSB-C
STM32Cortex-M4USB-CSPI FlashCompact Layout
View details

PTM-01 — Power Train Module

Design stage Power Electronics

Power-train monitoring module with current and voltage measurement, MOSFET driver stages and hardware-level protection. Measurement data is reported to the main controller over CAN.

Katman / Layers2
Gerilim / Voltage35 V
Akım / Current20 A sürekli · 30 A tepe
Boyut / Size120 × 250 mm
MCUSTM32 F serisi
MOSFET DriverShunt SensingCANHardware Protection

BMS-01 — Battery Management System

Design stage Battery Systems

Battery management board with cell monitoring, passive balancing and protection layers. Overcharge, temperature and short-circuit protection are handled at hardware level.

Katman / Layers2
Gerilim / Voltage35 V
Akım / Current20 A sürekli · 30 A tepe
Boyut / Size120 × 120 mm
MCUSTM32 F serisi
Cell MonitoringBalancingCAN + OptoThermal Sensing

NAU-01 — Navigation & Attitude Unit

Design stage Sensor Systems

Sensor-fusion board combining accelerometer, gyroscope and magnetometer data for orientation and motion analysis. Designed with an isolated reference plane and EMI-shielded I²C/SPI routing.

Katman / Layers4
Gerilim / Voltage12 V
MCUSTM32 F serisi
Arayüz / InterfaceI²C · SPI · CAN
IMUSensor FusionEMI ShieldingCAN

DCU-01 — Data & Communication Unit

Design stage Communication Systems

Central communication board managing data traffic between sub-modules. Includes isolated data paths, ESD-filtered connectors and CRC-based data validation.

Katman / Layers4
Gerilim / Voltage12 V
MCUSTM32 F serisi
Protokol / ProtocolsCAN · UART · RS-485
CANRS-485ESD ProtectionCRC

HMI-01 — Human Machine Interface

Design stage User Interface

LCD-based interface board that displays system status and handles user input. Uses a solid reference plane for the capacitive buttons and a separate supply rail for the backlight.

Katman / Layers2
Ekran / DisplayLCD / TFT sürücü
Arayüz / InterfaceUART · CAN
Giriş / InputKapasitif tuş takımı
HMILCDCapacitive InputUART

Blood Slide Stainer Main Control Board

Design stage Medical Device

Module and power-distribution board for a laboratory blood slide stainer. A single STM32F4 controller runs the pump motors, rack and drawer electromagnets, fans and a Peltier module, and reads the level and waste sensors. Power from a single input is distributed to 12 V, 5 V and 3.3 V rails by three switching regulators.

Katman / Layers2
Boyut / Size200 × 90 mm
Bileşen / Components181
MCUSTM32F4 · LQFP100
Besleme / Power3 × XL4015 · 12 V / 5 V / 3,3 V
Sürücüler / Drivers2 × VNH2SP30 · 2 × TB6612FNG
STM32Motor DriverBuck ConverterOptocouplerRS-232
View details

About development status

The boards below were developed as part of R&D work; the status of each is shown on its card. None has entered series production. The technical data is based on the design files and design targets.

Have a hardware idea?

Let's talk through the scope and technical constraints — I'll come back with a clear picture of the steps and the time it takes.